www.silverlinetools.com
5
7.2V Li-Ion Cordless Multi-Tool
959516
Work Area Safety
a)
Keep work area clean and well lit.
Cluttered or dark areas invite
accidents
b)
Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust.
Power tools
create sparks which may ignite the dust or fumes
c)
Keep children and bystanders away while operating a power
tool.
Distractions can cause you to lose control
Electrical Safety
a)
Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock
b)
Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators.
There is an increased
risk of electric shock if your body is earthed or grounded
c)
Do not expose power tools to rain or wet conditions.
Water enter-
ing a power tool will increase the risk of electric shock
d)
Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat,
oil, sharp edges or moving parts.
Damaged or entangled cords
increase the risk of electric shock
e)
When operating a power tool outdoors, use an extension cord
suitable for outdoor use.
Use of a cord suitable for outdoor use
reduces the risk of electric shock
f)
If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply.
Use of an RCD
reduces the risk of electric shock
NOTE:
The term “residual current device (RCD)” may be replaced by
the term “ground fault circuit interrupter (GFCI)” or “earth leakage
circuit breaker (ELCB)”.
Personal Safety
a)
Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while you
are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in
serious personal injury
b)
Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes,
hard hat, or hearing protection used for appropriate conditions will
reduce personal injuries
c)
Prevent unintentional starting. Ensure the switch is in the
off-position before connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with
your finger on the switch or energising power tools that have the
switch on invites accidents
d)
Remove any adjusting key or wrench before turning the power
tool on.
A wrench or a key left attached to a rotating part of the
power tool may result in personal injury
e)
Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations
f)
Dress properly. Do not wear loose clothing or jewellery.
Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts
g)
If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and prop-
erly used.
Use of dust collection can reduce dust-related hazards
Power Tool Use & Care
a)
Do not force the power tool. Use the correct power tool for your
application.
The correct power tool will do the job better and safer
at the rate for which it was designed
b)
Do not use the power tool if the switch does not turn it on and
off.
Any power tool that cannot be controlled with the switch is
dangerous and must be repaired
c)
Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive
safety measures reduce the risk of starting the power tool ac-
cidentally
d)
Store idle power tools out of the reach of children and do not al-
low persons unfamiliar with the power tool or these instructions
to operate the power tool.
Power tools are dangerous in the hands
of untrained users
e)
Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that
may affect the power tool’s operation. If damaged, have the
power tool repaired before use.
Many accidents are caused by
poorly maintained power tools
f)
Keep cutting tools sharp and clean.
Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control
g)
Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working condi-
tions and the work to be performed.
Use of the power tool for
operations different from those intended could result in a hazardous
situation
Service
a)
Have your power tool serviced by a qualified repair person
using only identical replacement parts.
This will ensure that the
safety of the power tool is maintained
Battery Charger Safety
Use the battery charger correctly
• Refer to the section of this manual relating to use of the battery charger
before attempting to charge the battery.
• Keep your battery charger clean; foreign objects or dirt may cause a
short or block air vents. Failure to follow these instructions may cause
overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard
Product Familiarisation
1
Collet Nut
2
Thread Cover
3
LED work light
4
On/Off Button
5
Speed Display
6
Speed Selector Buttons
7
Charging Socket
8
Spindle Lock Button
9
41pcs Accessory Kit
10
Charger
Unpacking Your Tool
• Carefully unpack and inspect your tool. Familiarise yourself with all its
features and functions.
• Ensure that all parts of the tool are present and in good condition. If any
parts are missing or damaged, have such parts replaced before attempting
to use this tool.
959516_Z1MANPRO1.indd 5
21/02/2013 09:40
