Silverline 268895 Manual Download

Page: 6 / 40

Included accessories (not shown):

Blow-moulded case, 6 x screwdriver bits, 6 x nut drivers

Note:

This manual may be supplied with different package configurations and supplied

accessories may vary.

Intended Use

Battery-operated impact driver with high levels of torque suitable for medium duty tasks
such as driving screws, nuts, bolts & other fasteners.

Unpacking Your Tool

• Carefully unpack and inspect your new sander. Familiarise yourself with all its features

and functions

• Ensure that all parts of the tool are present and in good condition. If any parts are

missing or damaged, have such parts replaced before attempting to use this tool

Before Use

Removing a battery

• To remove the Battery (6) from the impact driver, press the Battery Release (7), then
slide the Battery off the Hand Grip (9)

WARNING:

DO NOT try to remove the Battery without pressing the Battery Release button.

The drill or Battery could be damaged.

Fitting a battery

1. To fit a charged battery, slide it into the Hand Grip (9) of the drill until it clicks and

locks into position

Note:

Make sure the Battery and Impact Driver are lined up correctly. If the Battery does

not slide into the Impact Driver easily, don’t force it. Instead, slide the Battery out of the
Impact Driver again, check the top of Battery and the Impact Driver battery slot are clean
and undamaged and that the contacts are not bent.

Setting up the battery charger

1.  If fitted, remove any battery from the Battery Charger (11)
2.  Insert the DC plug of the Charger PSU (14) into the rear of the Battery Charger
3.  Insert the mains plug of the Charger PSU into a suitable mains socket

Note:

The Green LED (12) on the Battery Charger will illuminate to indicate that the charger

is ready to charge the battery.

WARNING:

ONLY use this charger to charge the supplied battery or additional purchased

batteries that are specifically designed for this tool.

WARNING:

The charger is designed for indoor use only, and MUST NOT be used in damp

or wet conditions.

Charging the battery

WARNING:

Failure to follow the correct procedure when charging batteries will result in

permanent damage.

Note:

Normal charging time is 1 hour for a recently discharged battery. However, if the

Battery (6) has been left in a discharged state for some time, it may take up to 1.5 hours
to charge.

1. Slide a fully or partially discharged Battery into the Battery Charger (11)

Note:

Make sure the Battery and Battery Charger are lined up correctly. If the Battery does

not slide into the Battery Charger easily, don’t force it. Instead, remove the Battery, check
the top of Battery and the Battery Charger slot are clean and undamaged and that the
contacts are not bent.

2. Both the Green LED (12) and Red LED (13) will flash to show the Battery is being

assessed by the charger

3. Once charging commences, both LEDs will illuminate without flashing
4. When the Battery is fully charged only the Green LED will be illuminated

Note:

If both LEDs are not constantly illuminated after the charger has assessed the

Battery, this indicates a fault condition. Recheck the Battery is fully inserted into the
Battery Charger (11). Remove any material that may have fallen into the charger’s battery
socket, and make sure the contacts of both the Battery and the Battery Charger are clean,
untarnished and not damaged or bent.

Notes about battery charging:

• The battery should be charged at ambient temperatures between 10 and 40°C

(ideally around 20°C)

• After charging, allow 15 minutes for the battery to cool before use
• Ensure that the charger is disconnected from the mains supply after use, and is

stored correctly

• DO NOT leave batteries on charge for extended periods and NEVER store batteries

on charge

• The Battery Charger monitors battery temperature and voltage while charging. Remove

the Battery once charging has been completed to maximise charge cycles of the battery
and not waste power

• Batteries can become faulty over time, individual cells in the battery can fail and the

battery could short. The charger will not charge faulty batteries. Use another battery,
if possible, to check correct functionality of the charger and purchase a replacement
battery if a faulty battery is indicated

• DO NOT store Lithium-Ion battery packs in a discharged state long term. This can

damage the Lithium-Ion cells. For long-term storage, store batteries in a high charge
state disconnected from the power tool

• The capacity of batteries will reduce over time. After 100 charge cycles, the battery’s

operation time and the maximum torque performance of the drill will slightly reduce.
This decline will continue until the battery has minimal capacity after 500 charge cycles.
This is normal and not a fault with the battery pack

Fitting a driver bit

WARNING:

DO NOT fit any attachment with a maximum speed lower than the no load

speed of the machine.

1.  Pull the Collar (2) of the ¼" Bit Holder (1) forward, and insert the bit
2.  Release the Collar
3.  Pull on the bit to check that it is securely fitted. If the bit is not secure, repeat the

above procedure

Note:

Make sure screwdriver bits used are hardened and suitable for use with an

impact driver.

¼” Bit Holder

Collar

Battery Level Indicator

Motor Vents

Forward/Reverse Switch

Battery

Battery Release

LED Work Light