background image

 

Operation  

 

 

12 

 

Folding and Unfolding the Devil Boom 

 
Unfolding

The  boom  will  slide  free  from  the 

saddles when unfolded. Use the tractor hydraulic 
lever to slowly unfold one arm at a time until the 
hydraulic cylinder is fully extended.  

  

Folding:  

Fold the boom slowly, one arm at a 

time with the tractor hydraulics until the arm 
rests on the support saddle.  

  

Devil Boom Setup 

1.Unfold each arm using the tractor remotes. 
2.When the hydraulic ram is fully extended, the 

bolt through the end of the ram must go the 
whole way to the end of the slot (below). Even 
a small gap will result in a whipping outer 
section. 

 

3.When the ram is at the end of the slot, the 

spring washers on the boom side of the 
bracket (right side below) must be fully 
compressed. 

 

4.After the ram setup is complete, make sure the 

outer arm pushrod is extended out so it holds 
the outer section down when the ram is at full 
stroke (if the push rod is set too short, the 
outer section will whip). 

  

Foam Marker 

Refer to the Foam Marker Operator’s Manual for 
installation and operating procedures relevant to 
the foam marker. 
 

Spray Guns and Hose Reels 

To operate the spray gun prime the pump as per 
normal then open the relevant control lever, set 
to the desired pressure (max 20 Bar). Depress 
the trigger to spray.  

 
 

 

 

 
 
 

 
 
 
 
 
 
 
Filling the Main Tank using Bottom 
Connection (1100L only) 

The main tank can be filled through either the 
top lid or bottom cam lock connection. The 
bottom cam lock is preferred as it stops the 
chemicals frothing. It is also safer as the tank 
can be filled from ground level. The bottom fill is 
protected from back flow by a non-return valve 
inside the tank. 
 
Undo the catches and remove the cap from the 
bottom fill connection. Connect a filling hose with 
a 50mm cam lock coupling to the connection 

Always ensure that the boom is folded or 
unfolded in a safe area where it will not foul 
on any other objects. Look up before folding or 
unfolding to check for obstructions. Never fold 
or unfold near overhead power lines. Ensure 
that all bystanders are clear before moving the 
boom. 

Correct Setup 

Incorrect Setup 

Ram Slot 

Summary of Contents for Super 1100L Series





















Reviews: