SIGLENT SPD3303X Quick Start Manual Download | Manualshive

Page: 10 / 45

background image

SIGLENT

2 SPD3000X QuickStart

General Inspection

Please check the instrument according to the following steps.

1. Inspect the shipping container.

Keep the damaged shipping container or cushioning material until the contents

of the shipment have been completely checked and the instrument has passed

both electrical and mechanical tests.

The consigner or carrier will be responsible for damages to the instrument

resulting from shipment.

SIGLENT

would not provide free maintenance or

replacement.

2. Inspect the instrument.

If there are instruments found damaged, defective or failure in electrical and

mechanical tests, please contact

SIGLENT

.

3. Check the accessories.

Please check the accessories according to the packing list. If the accessories

are incomplete or damaged, please contact

SIGLENT

.

«
...
8
9
10
11
12
...
»

Summary of Contents for SPD3303X














































Reviews:

No comments

Related manuals for SPD3303X

Brand: IBM Pages: 66

Brand: Fagor Pages: 256

Brand: Nation Flooring Equipment Pages: 2

Brand: Narex Pages: 16

Brand: NARGESA Pages: 71

Brand: LANCMAN Pages: 32

MAG-8200 Series

Brand: Magna-Matic Pages: 10

Brand: Pulsar Pages: 6

Brand: Lambda Electronics Pages: 21

Brand: Neilsen Pages: 16

Brand: Far Tools Pages: 24

TRIO-PS-2G/3AC/24DC/40

Brand: Phoenix Contact Pages: 25

Brand: jobmate Pages: 16

Brand: Tactical Pages: 4

Brand: Arch Pages: 5

Brand: Power It! Pages: 17

Brand: KVT Pages: 87

Brand: Weller Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands