SIGLENT SPD3303X Quick Start Manual Download | Manualshive

Page: 13 / 45

background image

SIGLENT

SPD3000X QuickStart 5

Buttons for setting parameters

Press the button to turn on/off the waveform display interface;

Press the button to set series mode of CH1/CH2, and the logo

“

” displays at the same time;

Press the button to set parallel mode of CH1/CH2, and the logo

“

” displays at the same time;

Press the button to enter the LAN setting and storage function

interface

Press the button to enter timer setting interface

Press the button longer to turn on/off the keylock function and

shorter to turn to system information interface

Buttons for controlling the channel

Press the button to turn on/off all the channels;

Press the button to select CH1 as the current channel;

Press the button to select CH2 as the current channel;

Press the button to turn on/off the output of current

channel;

Press the button to turn on/off the CH3 output

«
...
11
12
13
14
15
...
»

Summary of Contents for SPD3303X














































Reviews:

No comments

Related manuals for SPD3303X

Brand: Navitar Pages: 6

Brand: Makita Pages: 13

Brand: Makita Pages: 16

Brand: Wacker Neuson Pages: 56

Brand: Feider Machines Pages: 15

X 18 V - MANUEL 3

Brand: Parkside Pages: 12

Brand: Unimac Pages: 15

Brand: Yamato Pages: 12

Brand: LIVARNO LUX Pages: 100

DAKE Force 25DA

Brand: Laguna Tools Pages: 15

Brand: RCS Pages: 8

PSI 8000 3U HS PV Series

Brand: Elektro-Automatik Pages: 76

Brand: Sturtevant Richmont Pages: 4

Brand: Altrad Pages: 128

Brand: Baileigh Pages: 24

Brand: IAN CANADA Pages: 15

Brand: SRC Pages: 6

Brand: RHINO Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands