SIGLENT SPD3303X Quick Start Manual Download

Page: 45 / 45

SIGLENT

SPD3000X QuickStart 37

Chapter 5 Service and Support

Maintain summary

SIGLENT

warrants that the products that it manufactures and sells will be free

from defects in materials and workmanship for a period of three years from the

date of shipment from an authorized

SIGLENT

distributor. If a product or CRT

proves defective within the respective period,

SIGLENT

will provide repair or

replacement as described in the complete warranty statement.

To arrange for service or obtain a copy of the complete warranty statement,

please contact your nearest

SIGLENT

sales and service office. Except as

provided in this summary or the applicable warranty Statement,

SIGLENT

makes no warranty of any kind, express or implied, including without limitation

the implied warranties of merchantability and fitness for a particular purpose. In

no Event shall

SIGLENT

be liable for indirect, special or Consequential

damages

Contact SIGLENT

MTR Add: 3/F, Building 4, Antongda Industrial Zone, 3rd Liuxian Road,

68 District, Baoan District, Shenzhen, P.R. CHINA

Tel: +86-755-36615186

E-mail:[email protected]

http://www.siglent.com

Summary of Contents for SPD3303X














































Search results

Summary of Contents for SPD3303X

Reviews:

Related manuals for SPD3303X

Brands by name

Popular brands

SIGLENT SPD3303X, Quick Start Manual

Search results

Summary of Contents for SPD3303X

Reviews:

Related manuals for SPD3303X

Brands by name

Popular brands