SIGLENT SPD3303X Quick Start Manual Download | Manualshive

Page: 11 / 45

background image

SIGLENT

SPD3000X QuickStart 3

Safety Considerations

To ensure that the instrument can work normally, please conduct necessary

inspection before using the SPD3303X/3303X-E

Input Power Requirement

The SPD3303X/3303X-E allows a 50Hz/60Hz frequency, and four levels of AC

power: 100V/120V/220V/230V. You can select wanted power voltage with the

“DIP Switch” at the rear panel according to the actual demand.

Warning

To switch to the wanted power voltage, please disconnect the power

cord first.

Electrical Check

Please use the power cord provided as accessory and connects the instrument

to AC power. Check the power as the following steps.

1. Connect the power supply

Warning

To avoid electric shock, please make sure that the instrument

is

grounded correctly.

2. Turn on the power switch

Press the button POWER to enter boot interface, and system return to the

default settings after a while.

«
...
9
10
11
12
13
...
»

Summary of Contents for SPD3303X














































Reviews:

No comments

Related manuals for SPD3303X

Brand: Caen Pages: 17

Brand: Lambda Pages: 56

Brand: Lakeshore Pages: 122

Brand: Q-tran Pages: 5

Brand: W & H Pages: 18

Brand: CCS Pages: 24

Brand: Parkside Pages: 28

Brand: MAIMAN ELECTRONICS Pages: 24

Brand: Radio Shack Pages: 13

Brand: Fastorq Pages: 6

Brand: Parkside Pages: 65

Brand: Ratio Pages: 48

Brand: Urrea Pages: 12

Brand: Delta Electronika Pages: 6

Brand: Bostitch Pages: 32

Brand: Parkside Pages: 55

Brand: SoundCraft Pages: 12

Brand: Maktec Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands