manualshive.com logo in svg

SIG KADET LT-40, Instruction Manual, Page: 44 / 49

Share
Download
SIG KADET LT-40 Instruction Manual Download Page 44

. 

 

Fuel Tank

 
219.

 
Pull the stopper cap out of the front of the fuel tank. Inside the tank there should be two brass tubes, one brass clunk 
weight, and a short piece of fuel line tubing. Shake the tank to get these parts out through the hole. You may have to reach 
inside the tank with a tweezers or needle nose pliers to get a hold of the fuel line tubing and pull it out (CAUTION: Don’t 
squeeze too hard and put a hole in the tubing). Now shake the tank a few more times to make sure there is no dirt or 
plastic shavings inside!

 
220.

 
Take a close look at the stopper cap. Rotate the front plastic cap, the middle rubber stopper, and the rear plastic cap until 
the holes line up. You should be able to see daylight through two of the three holes. NOTE: We will only be using two of 
the holes. Leave the third hole closed.

 
221.

 
Cut one of the brass tubes to 1-1/2" long - this will be the Fuel Feed Tube. Cut the other brass tube to 2" long - this will be 
the Vent Tube. A razor saw works well for cutting the brass tubing. Clean up the sawn end of the tubing with 220 grit 
sandpaper to remove any burrs or sharp edges that might cut the fuel line tubing later.

 
222.

 
Carefully poke the brass tubes through the two open holes in the stopper cap. Keep pushing the tubes in until 3/8" of tube 
sticks out in front of the stopper cap. (PLAN AHEAD: The two brass tubes should end up horizontally opposed to each 
other at the bottom of the stopper cap. The short fuel feed tube should be on the left side, and the long vent tube on the 
right.)

 
223.

 
Put the plain end of a 3/32" dia. drill bit about 1/4" inside the back end of the vent 
tube. Using the drill bit for leverage, slowly bend the back end of the vent tube 
upwards about 45º, or until the end of the tube is even with the top of the stopper 
cap.

 

 

 

 
224.

 
Cut the piece of fuel line tubing that came with the tank to 3-1/4" long. Slide one 
end of the tubing onto the brass clunk weight. Slide the other end of the tubing 
over the back end of the fuel feed tube.

 
225.

 
Insert completed assembly into the neck of the fuel tank. Rotate the stopper cap 
so the brass tubes are horizontal at the bottom of the stopper. Hold the tank up to 
a strong light and look inside to see if the vent tube is close to the top of the tank. 
Also check to see if the brass clunk weight inside the tank swings freely from 
side-to-side, whether the tank is right side up or upside down. If the clunk weight 
is hitting the back wall of the tank, take the stopper cap back out, shorten the 
length of the fuel line tubing a little, and then test again. When everything is right, 
tighten the screw in the stopper cap until the cap is snug in the neck of the tank.

226. Test the fuel tank for leaks! Fill your kitchen sink with water. Slip the 12" long 

piece of Fuel Line Tubing that came in the kit onto the tank’s vent tube. 
Submerge the tank in the water, holding your thumb firmly over the fuel feed 
tube. Blow air into the other end of the fuel line tubing and watch for air bubbles 
coming around the cap of the tank. If it’s leaking, tighten the screw in the cap a 
little at a time until the leaking stops.

 
227.

 
Cut the piece of 12" long Fuel Line Tubing into two 6" long pieces. Slip one piece onto the tank’s fuel feed tube and the 
other onto the vent tube. Run the loose ends of the fuel line tubing through the hole in the firewall at the same time that 
you are placing the tank in the fuselage.

Summary of Contents for KADET LT-40


















































Reviews:

No comments