manualshive.com logo in svg

SIG KADET LT-40, Instruction Manual, Page: 43 / 49

Share
Download
SIG KADET LT-40 Instruction Manual Download Page 43

. 

Receiver Battery Pack

 
212.

 
Wrap the battery pack with a single layer of 1/2" thick soft foam rubber to insulate it from engine vibration and shock. Use 
tape or rubber bands to hold the foam around the battery. Install the wrapped battery pack inside the nose of the model, 
under the fuel tank floor, in the position shown on the plan (fuselage side view). Try to keep the battery pack as far to the 
right side of the fuselage as possible to avoid interfering with the nose gear pushrod.
 

Receiver

 
IMPORTANT: Do not cut the antenna wire coming out of the receiver or attempt 
to fly your model with the antenna wire folded or coiled up! The antenna length is 
predetermined by the radio manufacturer for best signal reception. Shortening or 
lengthening the antenna wire can detune the receiver.

 

 
213.

 
Drill a 1/16" dia. hole completely through the bottom of the fuselage, about 3-1/2" 
behind the firewall. This hole is for the receiver antenna wire to exit the fuselage. 
Make sure the hole will miss the battery pack before you start drilling! Put a single 
drop of Thin CA glue on the hole to keep the covering from coming loose.
 
Let dry completely! NOTE: These instructions describe running the antenna outside along the bottom of the fuselage. 
There are a lot of other ways to handle the routing of a receiver antenna. If you prefer a different method, by all means use 
it. The main thing to keep in mind is that you should always strive to keep the antenna as far away as possible from all the 
servo and battery wires.

 
214.

 
Wrap the receiver with a single layer of 1/2" thick soft foam rubber to insulate it from engine vibration and shock. Use tape 
or rubber bands to hold the foam around the receiver.

 
215.

 
Following the radio manufacturer’s instructions, plug all the wires for the servos, battery pack, and switch harness into the 
receiver so the radio system is fully operational. Double check to be sure that each servo is plugged into its correct 
receiver terminal and that it is responding properly. 
NOTE: Since the receiver will be hard to get at, you should use a short "extension" wire (available from the radio 
manufacturer) for the ailerons. Plug the extension wire into the receiver’s aileron terminal. Whenever you take the wing 
on/off the model, you can connect/disconnect the ailerons at the plug-in between the extension wire and the servo wire, 
leaving the extension wire itself permanently plugged into the receiver.

 
216.

 
Install the wrapped receiver inside the nose of the model, right behind the battery 
pack. Before you get the receiver completely in place, poke the antenna wire 
down through the hole in the bottom of the fuselage (use an "antenna strain 
relief" fitting if one came with your radio). Make sure the antenna wire is not 
tangled up in the servo and battery wires! Continue pulling the antenna out the 
bottom of the fuselage as you slide the receiver forward against the battery pack. 
If the receiver seems loose in the nose of the model, pack additional pieces of 
foam rubber around it to make sure it cannot move around in flight.

 

 
 

 
217.

 
Anchor the loose end of the antenna on the outside of the model near the rear of 
the fuselage using a small rubber band and a T-Pin (an "antenna hook" is also 
handy if one came with your radio). Stick the T-Pin into the bottom of the fuselage 
at an angle, as shown. Put a drop or two of Slow CA glue on the pin to keep it in 
place. Tie the rubber band to the antenna (or the antenna hook) and then loop it 
over the T-Pin. The antenna should be just taught, not tight! The rubber band 
allows a certain amount of give in case the antenna is snagged by accident.

 
218.

 
Cut an opening in the left side of the fuselage (the side away from the exhaust) to 
accommodate the radio’s on/off switch. Use the switch cover plate as a guide to 
mark the location and size of the opening and the two holes for the mounting 
screws. Install switch.

 
CAUTION: Make sure the opening you cut for the switch’s on/off lever is just slightly bigger than the lever, so that the 
switch will operate safely, without catching or binding on the wood.

Summary of Contents for KADET LT-40


















































Reviews:

No comments