Siemens SITRANS T4200 Operating Instructions Manual Download

Page: 40 / 100

Functional safety

7.2 Device-specific safety instructions

SITRANS TH200/TH300
Operating Instructions, 06/2010, A5E00393069-03

7.2

Device-specific safety instructions

7.2.1

Safety function

Measuring temperature is the safety function with the temperature transmitters.
It is applicable for output currents from 4 to 20 mA and ensures an accuracy of ± 2% in the

maximum measurement range.
The output value will be updated at least every 620 ms (filter time constant of the electrical

damping = 0 s).
The partial system is of type B. The calculations are valid for the operating mode with low

demand rate in single-channel operation. The specific values are listed in the manufacturer

declaration for the product (Declaration of Conformity, Functional Safety according to IEC

61508 and IEC 61511): Certificates / EC declaration of conformity (Page 85) .

7.2.2

Requirements

The temperature transmitter meets the following requirements:
● Functional safety to SIL 2 under IEC 61508 or IEC 61511-1, from firmware version FW:

as of 1/1/2004 (with order option C20 only)

●  Explosion protection for corresponding versions
●  Electromagnetic compatibility in compliance with EN 61326
●  EC Declaration of Conformity

Summary of Contents for SITRANS T4200





































































































Search results

Summary of Contents for SITRANS T4200

Reviews:

Related manuals for SITRANS T4200

Brands by name

Popular brands

Siemens SITRANS T4200, Operating Instructions Manual

Search results

Summary of Contents for SITRANS T4200

Reviews:

Related manuals for SITRANS T4200

Brands by name

Popular brands