Siemens SITRANS T4200 Operating Instructions Manual Download

Page: 23 / 100

Installation

4.3 Installation on DIN rail and G rail

SITRANS TH200/TH300

Operating Instructions, 06/2010, A5E00393069-03

4.3

Installation on DIN rail and G rail

CAUTION

Electromagnetic compatibility
If the sensor is installed outside a closed building, you must check the transmitter for

correct functioning following a lightning stroke.

Note
Fixing rings
The fixing rings included in the scope of delivery for the transmitter are not required for the

installation on DIN rails or G rails.

You can either install the transmitter on a 35 mm DIN rail or on a 32 mm G rail.

DIN EN 60715 applies to DIN rails and G rails in this context. The DIN rail adapter required

for installation can be ordered as an accessory under the Order No. 7NG3092-8KA.
Adhere to the ambient conditions specified in the technical data.

Figure 4-1

Securing the transmitter on DIN rails

Figure 4-2

Securing the transmitter on G rails

Summary of Contents for SITRANS T4200





































































































Search results

Summary of Contents for SITRANS T4200

Reviews:

Related manuals for SITRANS T4200

Brands by name

Popular brands

Siemens SITRANS T4200, Operating Instructions Manual

Search results

Summary of Contents for SITRANS T4200

Reviews:

Related manuals for SITRANS T4200

Brands by name

Popular brands