Siemens SITRANS T4200 Operating Instructions Manual Download

Page: 17 / 100

Description

3.5 Communication

SITRANS TH200/TH300

Operating Instructions, 06/2010, A5E00393069-03

3.5

Communication

3.5.1

Overview

SITRANS TH200

This device version does not have an interface to HART. Assigning the parameters to the

SITRANS TH200 is only possible "offline" using the modem for SITRANS

TH100/TH200/TR200.

SITRANS TH300

The device has a parameter assignment interface according to the HART specification. The

parameter assignment interface permits access to all the functions of the device via a HART

modem or a HART communicator. Connect the HART modem or the HART communicator in

accordance with the Fig. "HART communication with supply from voltage source".

WARNING

Only operate intrinsically safe HART modems or HART communicators on intrinsically safe

circuits. Be sure that the intrinsically safe parameters are observed.

Summary of Contents for SITRANS T4200





































































































Search results

Summary of Contents for SITRANS T4200

Reviews:

Related manuals for SITRANS T4200

Brands by name

Popular brands

Siemens SITRANS T4200, Operating Instructions Manual

Search results

Summary of Contents for SITRANS T4200

Reviews:

Related manuals for SITRANS T4200

Brands by name

Popular brands