manualshive.com logo in svg

Siemens SITRANS F US SONOKIT, Operating Instructions Manual, Page: 27 / 95

Share
Download
Siemens SITRANS F US SONOKIT Operating Instructions Manual Download Page 27

 

Connecting 

 

5.2 Wiring the power supply and the output 

SITRANS FUS080 transmitter 
Operating Instructions, 07/2012, A5E03059912-02 

25

 

4.

 

Ground transmitter via grounding terminal (PE) on PCB. 

 

Note 

 

 

Sensor grounding 
To ensure identical potential for sensor and transmitter, a direct grounding of transmitter 

and sensor is recommended. 

5.

 

Tighten both transducer cable glands. 

 

 

6.

 

Make sure that transducer cables are not overbent. Minimum cable bend radius is 50 

mm. 

 

 

5.2

 

Wiring the power supply and the output 

The wiring of the power supply and the output is done in three steps: 
1.

 

Wiring the power supply 

2.

 

Wiring the pulse output (if relevant) 

3.

 

Mounting the transmitter 

5.2.1

 

Wiring the power supply 

 

WARNING 

 

Make sure the power supply requirements stated on the nameplates are met! 

 

Summary of Contents for SITRANS F US SONOKIT
































































































Reviews:

No comments