manualshive.com logo in svg

Siemens SINAUT MD720-3, System Manual, Page: 69 / 76

Share
Download
Siemens SINAUT MD720-3 System Manual Download Page 69

Service functions 

SINAUT MD720-3 
C79000-G8976-C211 

69

 

Upload a new firmware into the SINAUT MD720-3 

When the service connection is established, you can start to upload the new 
firmware. 

1.  With Notepad (belongs to Windows) create a file with the name 

!cmdfile

. The 

file name must not have any extension (e.g.: .txt). The first line in this file is: 
STORE FirmwareName.BIN 
Instead of „FirmewareName.BIN“ write the name of the new firmware file.   

2.  At the Ftp>-prompt enter: 

put 

FirmwareName.BIN 

Press Enter. Instead of „FirmewareName.BIN“ write the name of the new 
firmware file. 

3.  Then at the Ftp>-prompt enter: 

put !cmdfile  

Press Enter.

  

After the firmware file and the !cmdfile file are successfully uploaded the 
SINAUT MD720-3 will start to install the new firmware. This process can last 
up to 10 minutes. After this the SINAUT MD720-3 restarts. Then the SINAUT 
MD720-3 is ready again. 

The firmware update is ready, if: 

• 

the LED “Q” is ON and the LED “C” blinks (MD720-3 with SIM card) 

or 

• 

the LED “S” blinks and the LED “C” is ON (MD720-3 without SIM card). 

Release the local service connection 

Release the local service connection, if you do not need it anymore. 

1.  At the Ftp>-prompt enter:

 quit 

Then press Enter. 

2.  Then also tear-down the network connection to the device. To do so right-click 

the icon in the Windows task bar. 
 

 

Summary of Contents for SINAUT MD720-3













































































Reviews:

No comments