manualshive.com logo in svg

Siemens SINAUT MD720-3, System Manual, Page: 43 / 76

Share
Download
Siemens SINAUT MD720-3 System Manual Download Page 43

SINAUT MD720-3 in Terminal Mode 

SINAUT MD720-3 
C79000-G8976-C211 

43

 

 

AT+CPMS 

Preferred Message Storage 

Test

 

Command: 

AT+CPMS=? 

Response: 

+CPMS: (list of supported <mem1>s),(list of supported <mem2>s),(list of supported 
<mem3>s), 
OK 

Read command 

Command: 

AT+CPMS?

 

 

Response: 

+CPMS: <mem1>,<used1>,<total1>,<mem2>,<used2>,<total2>,<mem3>, 
<used3>,<total3> 
OK 

Executive command 

Command: 

AT+CPMS=

 

<mem1>,<mem2>,<mem3>

 

Response: +CPMS: 

<used1>,<total1>,<used2>,<total2>,<used3>,<total3> 

OK 

Parameter: 

The executive command selects the SMS storage <mem<x>>, being used to read, write, 
etc.  
<mem1>  
Memory to be used for listing, reading and deleting of messages: 
“SM” 

Message storage on SIM card 

“ME” 

Message storage on device 

“MT” 

Sum of message storage on SIM card and device 

<mem2>  
Memory to be used for writing and sending of messages: 
“SM” 

Message storage on SIM card 

“ME” 

Message storage on device 

“MT” 

Sum of message storage on SIM card and device  

<mem3>  
Memory to be used for storage of received messages, if the routing to the connected 
application is not possible. Refer to command AT+CNMI with parameter <mt>=2 
“SM” 

Message storage on SIM card 

“MT” 

Sum of message storage on SIM card and device  

<usedx>  
Number of messages currently stored in <memx>. 
<totalx> 
Number of messages currently which can be stored in<memx>. 

Notice: Example: 

AT+CPMS=? +CPMS: 

("ME","SM","MT") 

 OK 
AT+CPMS? +CPMS: 

"ME",0,100 

 OK 
AT+CPMS="ME" +CPMS: 0,100 
 OK 
Until firmware version 1.6 inclusive, only the message storage “MT could be selected for 

Summary of Contents for SINAUT MD720-3













































































Reviews:

No comments