Siemens SINAUT MD720-3 System Manual Download Page 65

Page: 65 / 76

Service functions

SINAUT MD720-3
C79000-G8976-C211

6.2

Getting the current settings and values

Connect your PC to the interface X1 and start a terminal software, e.g.
HyperTerminal. Select the used COM interface of the PC and configure the
character format and the baudrate to the same settings as the X1 interface of the
SINAUT MD720-3.

By factory default the SINAUT MD720-3 has the following settings:

Baudrate

9600 Bit/s (in OPC Mode) or

19200 Bit/s (in Terminal Mode)

Character

format

8N1

When you push the SET button (less than 2 seconds) the correct IP configuration
of the SINAUT MD720-3 is shown by the terminal software.

Assigned-IP:

Assigned IP address (OPC Mode)

Remote-Host:217.6.61.22

IP address of the OPC servers (OPC Mode)

Destination-Port:20030

Port address of the OPC server (OPC Mode)

Source-Port:26863

Own port address (OPC Mode)

Remote-Host2:

Reserved

Destination-Port2:26862

Reserved

Source-Port2:RANDOM

Reserved

Server-Mode:TSC

Reserved

Server-Line:LL

Reserved

Server-Username:st

User

name

at the OPC server (OPC Mode)

Server-Username2:G21

Reserved

Dial-Up:GPRS

Reserved

System-Time:1894

System time since last restart

Terminal-Mode:DISABLE

Active mode: Terminal mode or OPC Mode

Firmware-Version:V.1.2.0

Firmware-Version

SIM-STATUS:SIM-OK SIM/PIN-Status
Provider:

GSM-Operator

NetID:

ID of the GSM-Operator

APN:

APN of the GPRS network

Quality:99

Receive

quality

(CSQ-

value)

COM-Control:DTR

Reserved

COM-Baudrate:9600

Baudrate

interface

COM-Format:8E1

Character format on X1 interface

Summary of Contents for SINAUT MD720-3













































































Search results

Summary of Contents for SINAUT MD720-3

Reviews:

Siemens SINAUT MD720-3, System Manual, Page: 65 / 76

Search results

Summary of Contents for SINAUT MD720-3

Reviews: