manualshive.com logo in svg

Siemens SINAUT MD720-3, System Manual, Page: 24 / 76

Share
Download
Siemens SINAUT MD720-3 System Manual Download Page 24

SINAUT MD720-3 in Terminal Mode 

 

SINAUT MD720-3 

24 

C79000-G8976-C211 

4.2 

Operating requirements in Terminal Mode: GPRS 
subscriber contract 

To use the SINAUT MD720-3 in Terminal Mode it is required: 

• 

SIM card of a GSM network operator including CSD data service 9600 Bit/s 
and an extra telephone number for data calls, 

• 

Availability of a GSM network.  

 

4.3 

Functions of the LEDs in Terminal Mode 

The device has 3 LEDs, which indicates the current operation status: 

 

S

 (Status) 

Q

 (Quality) 

C

 (Connect) 

 

LED Status 

Meaning 

Fast lighting in sequence 

Boot procedure 

Synchronous slow blinking 

Service mode 

Slow lighting in sequence 

Update 

S, Q, C

 

combined

 

Synchronous fast blinking 

Error 

Blinks slowly 

Device waiting for PIN input 

S (Status) 

Blinks fast 

PIN error / SIM error 

Blinks slowly 

Booking into GSM network 

1x intermittent blinking 

Field strength not sufficient 

2x intermittent blinking 

Field strength sufficient 

3x intermittent blinking 

Field strength medium 

ON permanently 

Field strength high 

Q (Quality) 

OFF 

Waiting for PIN input 

C (Connect) 

Blinks  

Terminal mode active 

 

Blinks slowly: 1 time each second 

Blinks fast: 4 times each second 

 
 
 
 

Summary of Contents for SINAUT MD720-3













































































Reviews:

No comments