manualshive.com logo in svg

Siemens SINAUT MD720-3, System Manual, Page: 66 / 76

Share
Download
Siemens SINAUT MD720-3 System Manual Download Page 66

Service functions 

 

SINAUT MD720-3 

66 

C79000-G8976-C211 

6.3 

Service mode to upload a new firmware 

When the service mode is active you can update the firmware of SINAUT MD720-
3.  

The firmware contains the fundamental programming of the SINAUT MD720-3. If 
the manufacturer has produced new firmware, for example to equip the device with 
new functions, then this can be loaded into the SINAUT MD720-3. 

You can find the latest firmware in the internet on the pages of des Siemens 
Service & Support (see Foreword). 

To update the firmware please proceed as follows. 

Switch on the service mode and connect the device to a PC 

1.  Push the SET button for 2 up to 4 seconds until the LED “Q” in ON, while the 

SINAUT MD720-3 is in operation. The device switches into the service mode. 

2.  Connect a PC to the interface X1 of the SINAUT MD720-3. 

Installation of the modem driver 

For the communication with the SINAUT MD720-3 in service mode you need to 
install a modem driver. 

1. Open 

the 

Control Panel

 in the Start Menu. 

2.  Using Windows XP opens the category 

Printers and Other Hardware 

or switch 

to the Classic View. 

3. Open 

the 

Phone and Modem Options

. 

4. Select 

Add

 in the register 

Modems

. 

5.  Please follow the 

Hardware-Wizard

. 

6. Select 

Don’t detect my modem; I will select it from a list a

nd click 

Next.

 

7.  Select from the manufacturer list 

Standard Modem Types

 the 

Standard 19200 

bps Modem

 and click 

Next.

 

8.  Select the COM-Port of your computer, the SINAUT MD720-3 is connected to 

and clicks 

Next.

 

9.  Wait until the modem installation has been finished and click 

Finish

. 

10. In the 

Phone and Modem Options

 menu the 

Standard 19200 bps 

Modem is 

listed now. 

Summary of Contents for SINAUT MD720-3













































































Reviews:

No comments