Siemens SIMOTION D410-2 Manual Download

Page: 64 / 94

Technical data

4.4 Interfaces and performance features

SIMOTION D410-2

Manual, 02/2012

Integrated drive control

Table 4- 8

Controls for integrated drives

Max. number of axes for integrated

drive control

(servo / vector / V/f)

1 / 1 / 1 (alternative)

drive control based on SINAMICS S120 CU310-2, firmware

version V4.x

4.4.2

Communication

Interfaces

Table 4- 9

Interfaces

DRIVE-CLiQ interface

Ethernet interface

PROFIBUS interface

•

Equidistant and isochronous

•

Can be configured as master or slave

Address space

Table 4- 10 Address space

Logical I/O address space

8 KB

Physical I/O address space, each PROFIBUS interface,

each inputs and outputs

1 KB

Permanent process image for BackgroundTask (I/O variables) 64 bytes
Additional configurable process image for each cyclic task (I/O

variables)

Yes

Address space for each PROFIBUS DP station

244 bytes

Address space per SINAMICS Integrated (PROFIBUS

Integrated)

512 bytes

Summary of Contents for SIMOTION D410-2































































































Search results

Summary of Contents for SIMOTION D410-2

Reviews:

Related manuals for SIMOTION D410-2

Brands by name

Popular brands

Siemens SIMOTION D410-2, Manual

Search results

Summary of Contents for SIMOTION D410-2

Reviews:

Related manuals for SIMOTION D410-2

Brands by name

Popular brands