Siemens SIMATIC IPC1047 Operating Instructions Manual Download Page 88

Page: 88 / 136

Device maintenance and repair

7.5 Removing and installing hardware

SIMATIC IPC1047

Operating Instructions, 09/2018, A5E45118479-AA

Removal

1. Use the LEDs to determine which

module is defective, e.g. the LED

④

lights red.
The LED

①

can also flash red

because there is a warning, e.g.

overload.

2. Alternatively, shut down the device.

Disconnect the power plug

②

from the

power supply module to be replaced.

3. Acknowledge the warning signal on the

LED

④

4. Tilt the handle

⑥

forward.

5. Unlock the power supply module at the

③

and pull the module

⑤

straight

forward out of the frame by the handle

⑥

6. Slide the new power supply module

into the frame all the way to the rear

until it clicks into place.

7. Reconnect the power plug

②

Alternatively, restart the device.

Both LEDs

①

and

④

light in green again.

7.5.4

Replacing the processor

Requirement

●

The device is opened.

●

A suitable processor
Only an approved processor is permitted to be installed on the motherboard of the

device. If the processor type is changed, the BIOS must be updated so that the suitable

microcode is loaded. Information about original spare parts for SIMATIC IPCs is available

on the Internet at:
–

Contacts (

http://www.siemens.com/automation/partner

)

–

SIMATIC IPC after-sales information system (

http://www.siemens.com/asis

)

Summary of Contents for SIMATIC IPC1047









































































































































Search results

Summary of Contents for SIMATIC IPC1047

Reviews:

Siemens SIMATIC IPC1047, Operating Instructions Manual, Page: 88 / 136

Search results

Summary of Contents for SIMATIC IPC1047

Reviews: