Siemens SIMATIC IPC1047 Operating Instructions Manual Download Page 38

Page: 38 / 136

Installing and connecting the device

3.3 Connecting the device

SIMATIC IPC1047

Operating Instructions, 09/2018, A5E45118479-AA

3.3.3.2

Connecting a redundant power supply

Requirement

●

2 power cables

Procedure

Read the section "ESD guideline (Page 103)".

Removal

1. Connect the power plug

①

. The LED

②

lights up.

2. As soon as you connect the power plug, a

warning signal sounds because only one

power supply module is in operation. The

LED

④

flashes red.

Press the acknowledgment key

④

. The

warning signal stops.

3. Connect the power plug

③

The LEDs

②

and

④

light green.

Note
If only one power supply module is switched on or connected, or a module is defective, a

warning signal is emitted. The warning signal stops when the acknowledgment key is

pressed.

Summary of Contents for SIMATIC IPC1047









































































































































Search results

Summary of Contents for SIMATIC IPC1047

Reviews:

Siemens SIMATIC IPC1047, Operating Instructions Manual, Page: 38 / 136

Search results

Summary of Contents for SIMATIC IPC1047

Reviews: