manualshive.com logo in svg

Siemens SIMATIC IPC1047, Operating Instructions Manual, Page: 71 / 136

Share
Download
Siemens SIMATIC IPC1047 Operating Instructions Manual Download Page 71

 

Expanding and assigning parameters to the device 

 

6.5 Expansion cards 

SIMATIC IPC1047 
Operating Instructions, 09/2018, A5E45118479-AA 

71

 

After replacement of the RAID adapter card, configure it in the BIOS setup as follows: 

 

 

Note 
The key combination <CTRL+A> is only effective in "Legacy" mode. If the "Boot Type" 

parameter is set to "UEFI Boot Type in the "Boot" menu in the BIOS setup, the RAID 

hardware is configured by using the "Device Management" button in the BIOS selection 

menu. 

 

1.

 

Switch on the device. 

2.

 

During the boot phase, press the key combination <CTRL+A> when prompted to do so. 
If the "Boot Type" parameter is set to "Dual Boot Type" in the "Boot" menu in the BIOS 

setup and an EFI boot medium is available, you must press the <ENTER> key after 

having pressed the <CTRL+A> within 1 second. 
The system starts if you do not press the <ENTER> key in time. 

3.

 

Assign the parameters under "Controller Configuration" as follows: 

 

 

 

 

Note 
The settings shown correspond to the default setting in the delivery state of the device. 
Difference in the parameters compared to the default setting of the Hardware RAID 

adapter card after replacement: 

•

 

"Drives Write Cache = Disabled", which means the write cache of the hard disk is 

switched off. 

•

 

"Alarm Control = Disabled", which means the acoustic alarm in case of a fault is 

switched off 

 

Summary of Contents for SIMATIC IPC1047









































































































































Reviews:

No comments