Siemens SIMATIC IPC1047 Operating Instructions Manual Download Page 132

Page: 132 / 136

Glossary

SIMATIC IPC1047

132

Operating Instructions, 09/2018, A5E45118479-AA

Troubleshooting

Error cause, cause analysis, error correction

Trusted Execution Technology

Hardware implementation that allows secured execution of programs and applications. It is

only effective when all relevant system components, such as processors, operating systems

and applications are supported.

Wake on LAN

The Wake on Local area network (WOL) function allows the PC to be started via the LAN

interface.

Warm restart

The restart of a computer after a program was aborted. The operating system is loaded and

restarted again. The CTRL+ ALT+ DEL hotkey can be used to initiate a warm restart.

WLAN

Wireless LAN is a local network that transmits data via radio waves, infrared light or other

wireless technology. Wireless LAN is mainly used for mobile computer applications in office

or factory environments.

ZMM

Zero Maintenance Cache Protection Module is a functional unit of the SAS Raid controller

that stores data in the cache of the controller in the case of a voltage failure. This functional

unit is maintenance-free.

Summary of Contents for SIMATIC IPC1047









































































































































Search results

Summary of Contents for SIMATIC IPC1047

Reviews:

Siemens SIMATIC IPC1047, Operating Instructions Manual, Page: 132 / 136

Search results

Summary of Contents for SIMATIC IPC1047

Reviews: