Siemens SIMATIC Industrial Flat Panel IFP2200 Compact Operating Instructions Download Page 8

Page: 8 / 42

Overview

1.2 Scope of delivery

IFP2200 INOX MT ETH

Compact Operating Instructions, 03/2018, A5E42185570-AA

●

Chemical resistance to cleaning agents and disinfectants as described in section

"Chemical Resistance (Page 28)".

●

Food-grade mounting gasket, exchangeable

●

Rear clamping frame for even application pressure of the mounting gasket

●

Mounting cutout and interfaces correspond to the standard device.

1.2

Scope of delivery

Depending on the order, the scope of delivery includes:

●

1 × device

●

1 × accessory pack with the following contents:
–

1 mounting gasket

–

1 clamping frame

–

1 power supply connector

–

Mounting clips (see section "Mounting the device (Page 19)")

–

Product information, mounting instructions

●

3 × product information (approvals, explosion protection), individually enclosed

Summary of Contents for SIMATIC Industrial Flat Panel IFP2200











































Search results

Summary of Contents for SIMATIC Industrial Flat Panel IFP2200

Reviews:

Related manuals for SIMATIC Industrial Flat Panel IFP2200

Brands by name

Popular brands

Siemens SIMATIC Industrial Flat Panel IFP2200, Compact Operating Instructions

Search results

Summary of Contents for SIMATIC Industrial Flat Panel IFP2200

Reviews:

Related manuals for SIMATIC Industrial Flat Panel IFP2200

Brands by name

Popular brands