Siemens SCALANCE XR-300M PoE Series Compact Operating Instructions Download Page 72

Page: 72 / 92

Block architecture of the SCALANCE XR-300M PoE

The XR‑300M PoE handles the Ethernet frame traffic of the 24 ports with the aid of three switch
blocks.

• The three switch blocks are connected in series (block 1 via block 2 to block 3).

• Gigabit wire speed is possible within a block (max. 8 ports per block).

• Between the blocks there is a bandwidth of 1 gigabit/s available,that must be shared by all

ports for frame traffic between the blocks.

When operating solely with Fast Ethernet (100 Mbps), the XR devices support full wire speed via
all blocks.

P10

P11

P12

P13

P14

P15

P16

1 Gbit/s

Figure 8-1

Block architecture of the XR324‑4M

8.4

Other properties

Switching properties

Max. number of learnable addresses

8000

Aging time

30 sec

Switching technique

Store and forward

Latency

5 μs

Reconfiguration times for redundancy mechanisms

Redundancy mechanism

Reconfiguration times

HRP

300 ms

Standby link

300 ms

MRP

200 ms

Technical specifications
8.4 Other properties

SCALANCE XR-300M PoE

Compact Operating Instructions, 03/2022, A5E02661178-15

Summary of Contents for SCALANCE XR-300M PoE Series





























































































Search results

Summary of Contents for SCALANCE XR-300M PoE Series

Reviews:

Related manuals for SCALANCE XR-300M PoE Series

Brands by name

Popular brands

Siemens SCALANCE XR-300M PoE Series, Compact Operating Instructions

Search results

Summary of Contents for SCALANCE XR-300M PoE Series

Reviews:

Related manuals for SCALANCE XR-300M PoE Series

Brands by name

Popular brands