manualshive.com logo in svg

Siemens SCALANCE XR-300M PoE Series, Compact Operating Instructions

Share
Download
Siemens SCALANCE XR-300M PoE Series Compact Operating Instructions Download Page 51

6.4

Connecting functional ground

Grounding options

Grounding (functional ground) is via the mounting bracket on the device or via the bolts on the 
rear of the device.

Position

The connector for the grounding cable is in the center of the rear panel of the device, see section 
"Dimension drawings (Page 75)".

Grounding is via a screw-in or a pressed in grounding bolt, see section "Product overview 
(Page 19)".

Fitting screw in grounding bolts

1

2

①

Toothed washer

②

Grounding bolt

To fit the screw-in grounding bolts, follow the steps below:

1. Thread the toothed washer 

①

 onto the bolt.

2. Screw in the grounding bolt 

②

 with a maximum tightening torque of 2 Nm.

Connecting up functional ground

Screw-in grounding bolts

Pressed in grounding bolts

6

5

4

3

6

5

4

3

③

Grounding terminal with cable

Connecting up

6.4 Connecting functional ground

SCALANCE XR-300M PoE
Compact Operating Instructions, 03/2022, A5E02661178-15

51

Summary of Contents for SCALANCE XR-300M PoE Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands