Siemens NK8237 MP4.40 Installation, Function & Configuration, Commissioning Download

Page: 10 / 68

Introduction

Building Technologies

048_DMS_NK8237_ICC_MP4.40_A6V10316241_a_en.doc

Fire Safety & Security Products

06.2011

2.3

What has been changed in MP4.40

Here is the list of modifications included in this version for new functions and im-
provements.

Section, Page

Modifications

p.5

New STEP portal

4, p.12

Fig. 5, p.14

New mainboard NKM8001-A2

6.1.1, p.23

New installation kit

6.1.3, p.25

New MP4.40 software setup

7.8, p.49

New secure download

9.1, p.54 SNMP

monitoring

9.3, p.55

Enhanced NW8204 diagnostic tool

2.3.1 Documentation changes and corrections in this edition

Here is the list of corrections and improvements (not related to new software fea-
tures) included in this edition of the document.

Section, Page

Modifications

p.41

Acknowledgement and reset commands can only be set as
general actions

9.1, p.54

New Kernel update section

Summary of Contents for NK8237 MP4.40





































































Search results

Summary of Contents for NK8237 MP4.40

Reviews:

Related manuals for NK8237 MP4.40

Brands by name

Popular brands

Siemens NK8237 MP4.40, Installation, Function & Configuration, Commissioning

Search results

Summary of Contents for NK8237 MP4.40

Reviews:

Related manuals for NK8237 MP4.40

Brands by name

Popular brands