Siemens NK8237 MP4.40 Installation, Function & Configuration, Commissioning Download

Page: 11 / 68

System limits

Building Technologies

048_DMS_NK8237_ICC_MP4.40_A6V10316241_a_en.doc

Fire Safety & Security Products

06.2011

3 System

limits

The following describes the system limits for the NK8237 units.

Fire control units

The following control units are supported:



FC2020



FC2030



FC2040



FC2060



FT2040



FC722



FC724



FC726



FT744

Fire system topologies and max.connectivity



Up to 4 FC20xx/FC72x control units in

Ethernet

topologies.



Up to 16 units in

FCnet topologies via SAFEDLINK

, in mixed

Ethernet/FCnet

topologies, and in

Extended networking topologies

Fire control unit software version



FS20 Sinteso MP3.0; MP3.0 SR2



FS720 Cerberus PRO IP2; IP3; MP3.0 SR2

Detectors



Max 10,000. This includes all the physical elements of the FC20/FC720 control

units.

Modbus device/station

One Modbus protocol can be handled, either serial or TCP/IP:



Serial connection: one link as Modbus slave in RTU mode over an RS232 or

RS485 line.



TCP/IP connection: Modbus server for one TCP/IP client connection. Separate

Ethernet ports can be used for BACnet/IP and Modbus TCP/IP for maximum
protection of the safety network.

Interaction capabilities

Unlike other NK8000 units, the NK8237 does not support interactions.

I/O modules locally connected via I

Unlike other NK8000 units, the NK8237 does not support DF8000 I/O modules.

Summary of Contents for NK8237 MP4.40





































































Search results

Summary of Contents for NK8237 MP4.40

Reviews:

Related manuals for NK8237 MP4.40

Brands by name

Popular brands

Siemens NK8237 MP4.40, Installation, Function & Configuration, Commissioning

Search results

Summary of Contents for NK8237 MP4.40

Reviews:

Related manuals for NK8237 MP4.40

Brands by name

Popular brands