manualshive.com logo in svg

Siemens NK8237 MP4.40, Installation, Function & Configuration, Commissioning

Share
Download
Siemens NK8237 MP4.40 Installation, Function & Configuration, Commissioning Download Page 39

Configuration 

39 

Building Technologies

 

 048_DMS_NK8237_ICC_MP4.40_A6V10316241_a_en.doc

Fire Safety & Security Products 

 

06.2011

 

The Modbus protocol node is created under the Protocols folder. 
By default, the new node is named “Modbus protocol #1”. 

5. 

Select the new 

Modbus Protocol

 node. 

6. 

Drag and drop the selection to one of the NK8237 

COM

 ports. 

A link node is created under the COM port node. 

In the Node tab, the Serial parameters section contains the communication set-
tings. By default the physical communication is set as follows: 

19200, E, 8, 1

. 

7. 

If necessary, modify the 

Serial parameters

 in the 

Node

 tab of the link node. 

8. 

If 

RS485

 is used, enable the corresponding checkbox in the 

Node

 tab of  

 the 

COM

 port node. 

9. 

Select the 

Modbus Protocol

 link under the 

COM

 port node. 

10

 Drag and drop the selection to the 

Modbus Master

 node. 

A link node is created under the Modbus Master node. 

Summary of Contents for NK8237 MP4.40





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands