Siemens NK8237 MP4.40 Installation, Function & Configuration, Commissioning Download

Page: 17 / 68

Hardware Installation

Building Technologies

048_DMS_NK8237_ICC_MP4.40_A6V10316241_a_en.doc

Fire Safety & Security Products

06.2011

5 Hardware

Installation

There are various possible NK8237 installation scenarios. Namely:

Installation of NK8237 in existing cabinets

DIN-rail mounting (typical) in plastic housing.

Mounting of the NK8237 board in the control unit housing using card

holders

(NKA8011-A1

required).

Installation of a complete NE8000 cabinet including the NK8237 unit

The

installation

must be carried out by technically

qualified personnel

5.1

NK8237 Hardware Installation

Installation
1.

Install the NK8237 unit on the DIN rail.

Connect fire subsystems on the Ethernet line.

Connect the Modbus serial device line or the Modbus station Ethernet line.

If used, connect the power supply supervision module DF8090.

Connect power supply. See Fig. 10 p. 18 if using a DF8090 supervision module.

Do not connect or disconnect any device when the device is powered on!

Fig. 8 NK823x electrical interfaces (top view)

Fig. 9 Serial RS232-interfaces (bottom view)

Back

COM 1 (in place of

X104)

COM 2 (in place of

X105)

Back

X1: USB, not used

X3: Ethernet 1

X2: Ethernet 2

X103: Power Supply

3 2 1 6 … 1 8 … 1 2 1 2 1

X105: RS485

(in place of COM2)

X101: 1 output

X102: 3 inputs

X104: RS485

(in place of COM1)

Top view

Bottom view

Summary of Contents for NK8237 MP4.40





































































Search results

Summary of Contents for NK8237 MP4.40

Reviews:

Related manuals for NK8237 MP4.40

Brands by name

Popular brands

Siemens NK8237 MP4.40, Installation, Function & Configuration, Commissioning

Search results

Summary of Contents for NK8237 MP4.40

Reviews:

Related manuals for NK8237 MP4.40

Brands by name

Popular brands