manualshive.com logo in svg

Siemens MD-P1, User Manual, Page: 45 / 76

Share
Download
Siemens MD-P1 User Manual Download Page 45

Appendices 

 

Appendix D - Monitoring and Servicing the MD-P1 and MD-P1D Model Power Meters 

 

45 

Siemens Industry, Inc. 

 

125-201 

 

 

09/30/2019 

 

Appendix D - Monitoring and Servicing the MD-P1 and 
MD-P1D Model Power Meters 

There are multiple tasks that are typically completed with your Siemens MD-P1 and 
MD-P1D Power Meters before being installed. 

ViewPoint Service Software Tool Functionality 

The ViewPoint Service software is designed to operate on a laptop computer and 
interface to the MD-P1 or MD-P1D Power Meters through a USB cable connection. 
ViewPoint software is compatible with Windows® 7 (32- or 64-bit), Vista (32- or 64-bit), 
XP or 2000. 

When ViewPoint is connected to the power meter using a USB cable, power is 
provided to operate the meter from the USB port. No additional power wiring is needed 
for this setup and service mode. The service software tool will support a few commonly 
used service functions such as: 
●  Upload MD-P1 and MD-P1D Power Meter settings into ViewPoint for viewing within 

the service tool. 

●  Inspect the meter name, serial number and firmware revision. 
●  Inspect Current Transformer (CT) values and parameters. 
●  Inspect key real time measurement values (only if connected to load). 
●  Perform firmware upgrades for MD-P1 and MD-P1D Power Meters. 

Obtaining and Installing ViewPoint Software 

The ViewPoint software is free to MD-P1 an MD-P1D Power Meter users. It is typically 
shipped on a flash drive with each order. It is also available for free download. To 
download and install the software: 

1. 

Start Internet Explorer and navigate to 

http://www.dentinstruments.com/siemens/

 

2. 

Log in with User: 

siemens

, password: 

mdpowermeter.

 

3. 

Click the <

ViewPointInstaller_3

> link. 

4. 

Choose 

Save

, and save the file to the location of your choice. 

5. 

Open the file you saved from Step 4. 

6. 

When asked if you want to run the software, click 

Run

. 

7. 

Click 

Install

. (

NOTE:

 A USB driver is installed when you install the ViewPoint 

software.) 

8. 

Check or uncheck 

Run Viewpoint

, 

Show Readme

, or 

Create Desktop Shortcut

 

as desired. 

9. 

Click 

Finish

. 

Summary of Contents for MD-P1













































































Reviews:

No comments