Siemens MD-P1 User Manual Download Page 43 | Manualshive

Page: 43 / 76

Siemens MD-P1 User Manual Download Page 43

Appendices

Appendix C - MD-P1D with Visual Display

43

Siemens Industry, Inc.

125-201

09/30/2019

Appendix C - MD-P1D with Visual Display

The MD-P1D Power Meter features a backlit digital display. It has two rows of 16
characters that auto cycle between informational screens every two to three seconds,
with real-time values updated every second.

MODE SELECTION:

The meter display may be toggled between the

Auto Cycle

mode (default) or

Manual Cycle and Hold

mode by pushing/holding the meter display

button for > five seconds. This mode change is saved to non-volatile memory in case
of power loss.

AUTO CYCLE

: The display will auto cycle between flowchart screens every two

seconds. Pushing the meter display button > five seconds will temporarily hold the
current screen until either the display button is pushed again, or until a 20-second
(default) timeout occurs, returning it to Auto Cycle.

MANUAL CYCLE AND HOLD

: The display will manually advance the flowchart

screens by pushing the meter display button multiple times. The display screen will
remain in its last displayed mode, updating values continuously.

«
...
41
42
43
44
45
...
»

Summary of Contents for MD-P1













































































Reviews:

No comments