Siemens MD-P1 User Manual Download Page 30 | Manualshive

Page: 30 / 76

Siemens MD-P1 User Manual Download Page 30

1

Supported P1 Applications

MD-P1 and MD-P1D Power Meters Wiring Diagrams

30

Siemens Industry, Inc.

125-201

09/30/2019

Supported P1 Applications

The MD-P1 and MD-P1D Power Meters are factory pre-programmed for the following
applications when ordered in a kit with the appropriate current CTs:

Application

Usage

2671

50 Amp CTs

2672

1000 Amp CTs

2673

100 Amp CTs (default for MD-P1x-3-CTSC-100A)

2674

200 Amp CTs (default for MD-P1x-3-CTSC-200A)

2675

400 Amp CTs (default for MD-P1x-3-CTSC-400A)

2676

600 Amp CTs (default for MD-P1x-3-CTSC-600A)

2677

4000 Amp Rogowski Coil (default for MD-P1x-3-RC-xx)

2679

Universal (scaling must be set at the job site)

NOTE:

If an MD-P1 or MD-P1D Power Meter is ordered as a spare, it will leave the factory
configured for Application 2679.

NOTE:

If the P1 meter has firmware earlier than Revision 4.5, the application numbers use a
number that is 100 higher (for example, Application 2671 was 2771). Please update
older PI units to Revision 4.5 or higher to resolve a possible application number
conflict with other sensors.

«
...
28
29
30
31
32
...
»

Summary of Contents for MD-P1













































































Reviews:

No comments