manualshive.com logo in svg

Siemens MD-P1, User Manual, Page: 18 / 76

Share
Download
Siemens MD-P1 User Manual Download Page 18

 

Installation 

Connecting the MD-P1 and MD-P1D Power Meters 

 

18 

Siemens Industry, Inc. 

 

125-201 

 

 

09/30/2019 

 

Figure 6: Power Meter Connections. 

Completing the Wiring Connections - RS-485, 
Voltage Leads and CTs 

 

 

 

WARNING 

The FLN cable within electric panels and switchgear should be jacketed, shielded, 
twisted triad wire BELDEN 1121A. The jacket insulation rating should be 600V.  
 

DO NOT

 connect the FLN cable to the field panel yet. 

 

 

WARNING 

At this time, DO NOT connect the FLN cable to the FLN trunk. 

Doing so may damage FLN devices or cause personal injury. 

1. 

Mechanically secure the FLN cable where it enters the cabinet or panel. Remove 
the black RS-485 connector from the MD-P1 or MD-P1D Power Meter and wire the 
FLN cable to the RS-485 connector. Connect positive (+), and negative (-) wires to 
the FLN connector using the daisy-chain method (see Figure 6). Keep length of 
exposed wire to a minimum. 

2. 

Connect the COMMON wire to the RS-485 connector (S) terminal (see Figure 6).  

3. 

Tape back one of the FLN cable shields and connect the other shield to the Utility 
Panel Ground. 

4. 

If the MD-P1 or MD-P1D is the last FLN device, install the end of line terminator on 
the positive (+) and negative (-) terminals. See 

APOGEE Wiring Guidelines for 

Field Panels and Equipment Controllers

 (125-3002) for additional information. 

5. 

Tape or shrink wrap all FLN wire terminations and insulate any other exposed FLN 
wiring. Ensure that insulation complies with local and National Electrical Codes.  

Summary of Contents for MD-P1













































































Reviews:

No comments