manualshive.com logo in svg

Siemens MD-P1, User Manual, Page: 21 / 76

Share
Download
Siemens MD-P1 User Manual Download Page 21

Installation 

 

Connecting the MD-P1 and MD-P1D Power Meters 

 

21 

Siemens Industry, Inc. 

 

125-201 

 

 

09/30/2019 

 

 

 

WARNING 

USE ONLY SHUNTED CURRENT TRANSFORMERS (CTs). DO NOT USE 5A 
SECONDARY CTs OR UNSHUNTED CTs. 
Do not use other CTs. Only use shunted CTs with a 333 mV maximum output. 
Serious shock hazard and meter damage can occur if unshunted CTs are used. 
Use only the following Siemens Industry CTs that are UL listed/Recognized and have 
been evaluated to IEC 61010-1. See Figure 7. 

 

 

14. 

Connect electrical power to the power meter's red power connection plugs using 14 
AWG THHN (or equivalent) wires, after a building-installed, dedicated circuit 
disconnect breaker, as close as possible to the breaker. Mark the breaker as the 
disconnect for the meter. See 

Wiring Diagrams

 for specifics of the wiring 

connections. 

Follow local electrical codes during this installation. 

 

 

 

CAUTION 

Do not strap or mount an MD-P1 or MD-P1D Power Meter less than two inches 
from current carrying conductors. 

The magnetic field around the conductors may affect the electronics in the meter. 

 

 

 

The MD-P1 and MD-P1D Power Meters have an internal non-user replaceable 0.5 
Amp internal fuse protection. 

 

 

 

 

WARNING 

Do not exceed 600 Vac Phase-to-Phase CATIII. 

 

 

 

The MD-P1 and MD-P1D Power Meters are rated for measurement category III. 
These measurements are performed in the building installation. Examples are 
measurements on distribution boards, circuit breakers, wiring including cables, 
busbars, junction boxes, switches, socket outlets in a fixed installation, and 
equipment for industrial use. Other equipment could include stationary meters with a 
permanent connection to the fixed installation. 

Summary of Contents for MD-P1













































































Reviews:

No comments