manualshive.com logo in svg

Siemens MAMMOMAT 300, Installation And Start-Up Instructions Manual, Page: 8 / 93

Share
Download
Siemens MAMMOMAT 300 Installation And Start-Up Instructions Manual Download Page 8

Siemens-Elema AB

SPS-UD

RX B7-120.033.01.10.02

MAMMOMAT 300

Solna, Sweden

05.98

65 02 186

Prerequisites

1-3

Checking and recording for the DHHS area of application

In the area of application of the DHHS regulations, maintenance measurements must be 
made according to the instructions "DHHS Maintenance Schedule and User´s Spot 
Checks" RX B7-120.101... (included in the "DHHS Supplements to the operating instruc-
tions" RX B7-120.203...).

Sections

•

Required labels.

•

Radiation ON indicators.

•

Manual termination of exposure.

•

Checking the maximum adjustable mAs with the following kV-values.

•

Filters in beam limiting device (BLD).

•

Reproducibility.

•

kVp-accuracy.

•

mAs-accuracy.

•

Automatic exposure control (AEC).

•

Coincidence of radiation field/image receptor.

•

Alignment of light field/x-ray field.

•

Illuminance of light localizer (light field).

•

Shut-down of motor-driven compression movement.

The result must be recorded in "Measurement certificate" RX B7-120.037...

Some of the values to be determined can be taken from the acceptance test certificate.

The radiation-field limitation is set at the factory and recorded in the acceptance test cer-
tificate.

If the measurements to be made concerning the radiation-field limitation are within the 
tolerances stated in these instructions, this confirms that the settings made at the factory 
have not changed.

Note on delivery state

The MAMMOMAT 300 has been tested and adjusted at the factory, and should therefore 
be ready for operation after completion of the installation.

Summary of Contents for MAMMOMAT 300






























































































Reviews:

No comments