background image

Setting

Description

Device Name

The device name of the TiM2xx can be added
to the data measurement output. By default,
the device name is not included in the output.

Output interval

This setting is used to define the data mea‐
surement output at every scan cycle. Based on
the scanning frequency of 14.5Hz, the TiM2xx
provides 14.5 scans per second.
For example, if the 

Output interval

 is set to 3,

data measurement will only be available after
every third scan cycle of the device. The
default setting is 1 which equates to one data
measurement output per scan cycle.

Output data range

The output data range refers to the scanning
angle of the device. The default range is -120°
to +120°.

7.1.2

Network settings

The 

Interfaces

 view contains settings for configuring the Ethernet communication.

NOTE

1

TiM2xx supports 100Mbits/s communication speed with full duplex.

2

TiM2xx uses communication port 2111 for parametrisation as well as streaming
of measurement data. Maximum one connection is supported from a communica‐
tion controller to the device.

7.2

Reading measured data output

The section shows how to send telegrams via a terminal program using the SICK proto‐
col CoLa A (ASCII and hexadecimal values, with TCP port 2111) or CoLa B (binary/hexa‐
decimal values, with TCP port 2111) to TiM2xx.

OPERATION 

7

8025019/190A/2020-08 | SICK

O P E R A T I N G   I N S T R U C T I O N S | TiM2xx

25

Subject to change without notice

Summary of Contents for TiM2 Series





































Reviews: