background image

WARNING
Danger due to improper use!

Any improper use can result in dangerous situations.
Therefore, observe the following information:

Product should be used only in accordance with its intended use.

All information in these operating instructions must be strictly observed.

Shut down the product immediately in case of damage.

2.4

Cybersecurity

To protect against cybersecurity threats, it is necessary to continuously monitor and
maintain a comprehensive and holistic cybersecurity concept. A suitable concept com‐
prises organizational, technical, procedural, electronic, and physical levels of defense
and provides suitable measures for different types of risks. SICK's products and solu‐
tions must be viewed as a component of this concept.

Information on Cybersecurity can be found at

www.sick.com/psirt 

.

2.5

Limitation of liability

Relevant standards and regulations, the latest technological developments, and our
many years of knowledge and experience have all been taken into account when
compiling the data and information contained in these operating instructions. The
manufacturer accepts no liability for damage caused by:

Non-adherence to the product documentation (e.g., operating instructions)

Incorrect use

Use of untrained staff

Unauthorized conversions or repair

Technical modifications

Use of unauthorized spare parts, consumables, and accessories

NOTE
Programmable device

The Sensor Integration Machine (SIM) is a programmable device.
Therefore, the respective programmer is responsible for his/her programming perform‐
ance and the resulting operating principle of the device.
The liability and warranty of SICK AG is limited to the device specification (hardware
functionality and any programming interfaces) according to the agreed conditions.
Therefore, SICK AG is not liable, among other things, for damages that are caused by
programming of the customer or third parties.

2.6

Modifications and conversions

NOTICE

Modifications and conversions to the device may result in unforeseeable dangers.

Interrupting or modifying the device or SICK software will invalidate any warranty claims
against SICK AG. This applies in particular to opening the housing, even as part of
mounting and electrical installation.

SAFETY INFORMATION

8

O P E R A T I N G   I N S T R U C T I O N S | SIM1004

8023516/1BQH/2021-07-28 | SICK

Subject to change without notice

Summary of Contents for SIM1004































Reviews: