Shuttle HOT-565 User Manual Download Page 27 | Manualshive

Page: 27 / 33

background image

HOT- 565 User's Manual 27

HDD Power Down

This item

defines the continuous HDD idle time before the HDD enters

power saving mode (motor off). The options are from 1 min to 15 min and

Disabled

.

VGA Active Monitor

If this item is set to Enabled, the VGA activity event will be monitored to
reload global timer.

** Reload Global Timer Events **

If these items is set to Disabled, the system activity event will not be
monitored to reload global timer.

If these items is set to Enabled, the system activity event will be monitored
to reload global timer.

These items including IRQ[3-7, 9-15], NMI, Primary IDE0/1, Secondary
IDE 0/1, Floppy Disk, Serial Port and Parallel Port.

«
...
25
26
27
28
29
...
»

Summary of Contents for HOT-565


































Reviews:

No comments

Related manuals for HOT-565

Brand: Linear Pages: 10

Brand: Quick Pages: 28

Brand: DFI Pages: 92

DisplayPort VIP Input Board

Brand: Lattice Pages: 21

Brand: Gigabyte Pages: 39

Brand: Supermicro Pages: 1

Brand: Telit Wireless Solutions Pages: 49

SMART SPMXCA200

Brand: Spektrum Pages: 16

Brand: ASROCK Pages: 173

Brand: ASROCK Pages: 216

ZigBee RC2200DD

Brand: Radiocrafts Pages: 4

Brand: TYAN Pages: 42

Brand: TYAN Pages: 41

Brand: Ebyte Pages: 16

Brand: IBT Technologies Pages: 56

Brand: American Megatrends Pages: 72

Brand: Nash Pages: 30

EVAL-ADGS1612SDZ

Brand: Analog Devices Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands