Shuttle HOT-565 User Manual Download Page 31

Page: 31 / 33

HOT- 565 User's Manual 31

Onboard FDC Control

This item specifies onboard floppy disk drive controller. This setting allows
you to connect your floppy disk drives to the onboard floppy connector.
Choose the "

Disabled

" settings if you have a separate control card.

Onboard UART1/2

This item is used to define onboard serial port 1/Port2 to

3F8/IRQ4, 2F8/

IRQ3, 3E8/IRQ4, 2E8/IRQ3, Auto

Disabled

UR2 Mode

The main board support IrDA(HPSIR) and Amplitudes Shift Keyed
IR(ASKIR) infrared through COM 2 port. This item specifies onboard Infra
Red mode to

IrDA 1.0, ASKIR, MIR 0.57M, MIR 1.15M, FIR

Standard

(Disabled).

Note : FIR is not available currently.

IR Duplex Mode

This item specifies onboard infrared transfer mode to

full-duplex

half-

duplex.

This item will not show up when IrDA, ASKIR, or MIR UR2 modes

are selected.

Onboard Parallel Port

This item specifies onboard parallel port address to

378H, 278H, 3BCH

Disabled.

Parallel Port Mode

This item specifies onboard parallel port mode. The options are

SPP

(Standard Parallel Port),

EPP

(Enhanced Parallel Port),

ECP

(Extended

Capabilities Port), and

EPP+ECP.

ECP Mode Use DMA

This item specifies

DMA

(Direct Memory Access) channel when ECP

device is in use. The options are

DMA 1

and

DMA 3

This item will not

show up when SPP and EPP printer mode is selected.

Summary of Contents for HOT-565


































Search results

Summary of Contents for HOT-565

Reviews:

Related manuals for HOT-565

Brands by name

Popular brands

Shuttle HOT-565, User Manual

Search results

Summary of Contents for HOT-565

Reviews:

Related manuals for HOT-565

Brands by name

Popular brands