Shuttle HOT-565 User Manual Download Page 22 | Manualshive

Page: 22 / 33

background image

HOT- 565 User's Manual 22

Boot Up NumLock Status

When this option enables, BIOS turns on

Num Lock

when system is

powered on.

Boot Up System Speed

This option sets the speed of the CPU at system boot time. The settings are

High

or

Low

.

Typematic Rate Setting/Typematic Rate/Typematic Delay

This determines if the typematic rate and typematic delay are to be used.
When the typematic rate setting is enabled,

typematic rate

allows you

select the rate at which the keys are accelerated and

typematic delay

allows

you to select the delay between when the key was first depressed and when
the acceleration begins.

Security Option

This item allows you to limit access to the System and Setup, or just to
Setup.
When

System

is selected, the System will not boot and access to Setup will

be denied if the correct password is not entered at the prompt.
When

Setup

is selected, the System will boot, but access to Setup will be

denied if the correct password is not entered at the prompt.

PCI VGA Palette Snoop

This item must be set to enabled if there is a MPEG ISA card installed in
the system, and disabled if there is no MPEG ISA card installed in the
system.

OS Select For DRAM > 64MB

This item allows you to access the memory that over 64 MB in OS/2.

Video BIOS Shadow/XXXXX-XXXXX Shadow

These items determine whether Video BIOS or optional ROM will be
copied to RAM.

«
...
20
21
22
23
24
...
»

Summary of Contents for HOT-565


































Reviews:

No comments

Related manuals for HOT-565

Brand: Uctronics Pages: 27

Brand: JETWAY Pages: 56

A20-OLINUXINO-LIME

Brand: OLIMEX Pages: 49

Brand: Advantech Pages: 82

Brand: ASROCK Pages: 26

Brand: OMS Pages: 11

ConnectCore 6UL SBC Pro

Brand: Digi Pages: 54

Brand: DFI Pages: 177

Brand: Texas Instruments Pages: 20

GEO-SPOT GPS SW65/54

Brand: Watersnake Pages: 44

Brand: AZZA Pages: 61

Brand: MSI Pages: 118

Brand: Avalue Technology Pages: 92

Brand: NXP Semiconductors Pages: 7

Brand: Laird Pages: 17

Brand: Lantronix Pages: 20

Brand: NEC Pages: 16

Brand: NEC Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands