Shuttle HOT-565 User Manual Download Page 21 | Manualshive

Page: 21 / 33

background image

HOT- 565 User's Manual 21

BIOS Features Setup

CPU Internal/External Cache

This item enables CPU internal cache and external cache to speed up
memory access.

Quick Power On Self Test

This item speeds up Power On Self Test (POST) after you power on the
computer. If it is set to Enabled, BIOS will shorten or skip some check
items during POST.

Boot Sequence

This item determines which drive computer searches first for the disk
operating system. Default setting is A, C, SCSI.
BIOS also support system boot from CD-ROM drive or SCSI hard disk
drive.

Swap Floppy Drive

When this item enables, the BIOS will swap floppy drive assignments so
that Drive A: will function as Drive B: and Drive B: as Drive A:.

Boot Up Floppy Seek

During POST, BIOS will determine if the floppy disk drive installed is 40 or
80 tracks.

«
...
19
20
21
22
23
...
»

Summary of Contents for HOT-565


































Reviews:

No comments

Related manuals for HOT-565

Brand: MSI Pages: 169

Brand: Gigabyte Pages: 51

Brand: Infineon Pages: 24

Brand: ASROCK Pages: 39

Brand: ST Pages: 24

Brand: J&W Pages: 40

Brand: Intel Pages: 110

C807MS-E33 Series

Brand: MSI Pages: 124

Brand: ON Semiconductor Pages: 7

Brand: Texas Instruments Pages: 27

Brand: Maxus Pages: 59

Brand: Gigabyte Pages: 96

Brand: Supero Pages: 121

Brand: AZZA Pages: 61

Brand: DataExpert Pages: 44

S5U13781R00C10M

Brand: Epson Pages: 32

Brand: Epson Pages: 32

Brand: Epson Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands