Shuttle HOT-555 User Manual Download Page 16 | Manualshive

Page: 16 / 32

background image

HOT-555 User's Manual 16

Standard CMOS setup

This setup page includes all the items in a standard compatible BIOS.

BIOS features setup

This setup page includes all the items of Award special enhanced features.

Chipset features setup

This setup page includes all the items of chipset features.

Power Management Setup

This setup page includes all the items of Power Management features.

PCI Configuration setup

This category specifies the value (in units of PCI bus blocks) of the latency
timer for this PCI bus master and the IRQ level for PCI device. Power-on
with BIOS defaults

Load BIOS Defaults

BIOS defaults loads the values required by the system for the maximum
performance. However, you may change the parameter through the Option
Setup Menu.

The Main Menu

«
...
14
15
16
17
18
...
»

Summary of Contents for HOT-555

































Reviews:

No comments

Related manuals for HOT-555

Brand: Gigabyte Pages: 46

Brand: Gigabyte Pages: 74

Brand: Tadao Pages: 3

Brand: Intel Pages: 74

126791-HMC764LP6C

Brand: Analog Devices Pages: 18

Brand: Abit Pages: 72

Brand: NXP Semiconductors Pages: 40

Brand: EPC Pages: 6

Brand: Gigabyte Pages: 88

Brand: Zeal-All Pages: 8

Brand: Texas Instruments Pages: 20

Brand: Commell Pages: 53

Brand: IEI Technology Pages: 53

Brand: Intel Pages: 86

Brand: DFI Pages: 144

Brand: DFI Pages: 76

Brand: Suzuki Pages: 3

Brand: Abit Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands