Shuttle HOT-555 User Manual Download Page 28

Page: 28 / 32

HOT-555 User's Manual 28

IRQ 7 assigned to

The system BIOS will assign IRQ 7 to

legacy ISA

PCI/ISA PnP

IRQ7 default assign to legacy ISA for LPT1.

IRQ 9 assigned to

The system BIOS will assign IRQ 9 to

legacy ISA

PCI/ISA PnP

IRQ9 default assign to PCI/ISA PnP for PCI or ISA PnP devices.

IRQ 10 assigned to

The system BIOS will assign IRQ 10 to

legacy ISA

PCI/ISA PnP

IRQ10 default assign to PCI/ISA PnP for PCI or ISA PnP devices.

IRQ 11 assigned to

The system BIOS will assign IRQ 11 to

legacy ISA

PCI/ISA PnP

IRQ11 default assign to PCI/ISA PnP for PCI or ISA PnP devices.

IRQ 12 assigned to

The system BIOS will assign IRQ 12 to

legacy ISA

PCI/ISA PnP

IRQ12 default assign to PCI/ISA PnP for PCI or ISA PnP devices. Since
PS/2 mouse uses the same IRQ, if there are a PS/2 mouse on your system,
assign IRQ12 to legacy ISA to avoid system conflict.

IRQ 14 assigned to

The system BIOS will assign IRQ 14 to

legacy ISA

PCI/ISA PnP

IRQ14 default assign to legacy ISA for primary IDE controller.

IRQ 15 assigned to

The system BIOS will assign IRQ 15 to

legacy ISA

PCI/ISA PnP

IRQ15 default assign to legacy ISA for secondary IDE controller.

DMA-0, 1, 3, 5, 6, 7 assigned to

The system BIOS will assign DMAs to

legacy ISA

PCI/ISA PnP

DMA 0, 1, 3, 5, 6 and 7 channel default assign to PCI/ISA PnP.

Summary of Contents for HOT-555

































Search results

Summary of Contents for HOT-555

Reviews:

Related manuals for HOT-555

Brands by name

Popular brands

Shuttle HOT-555, User Manual

Search results

Summary of Contents for HOT-555

Reviews:

Related manuals for HOT-555

Brands by name

Popular brands