Shuttle HOT-555 User Manual Download Page 29

Page: 29 / 32

HOT-555 User's Manual 29

Integrated Peripherals

IDE HDD Block Mode

This category is used to set IDE HDD Block Mode. If your IDE Hard Disk
supports block mode, then you can enable this function to speed up the
HDD access time. If not, please disable this function to avoid HDD access
error.

IDE Primary/Secondary Master PIO

In this category, there are five modes defined in manual mode and one
automatic mode. There are

, and

AUTO

. The default settings

for on board Primary/Secondary Master PIO timing is Auto.

IDE Primary/Secondary Slave PIO

In this category, there are five modes defined in manual mode and one
automatic mode. There are

, and

AUTO

. The default settings

for on board Primary/Secondary Slave PIO timing is Auto.

On-Chip Primary PCI IDE

This category is used to defined on chip Primary PCI IDE controller is
"

Enable

" or "

Disable

" setting.

On-Chip Secondary PCI IDE

This category is used to defined on chip Secondary PCI IDE controller is
"

Enable

" or "

Disable

" setting.

Summary of Contents for HOT-555

































Search results

Summary of Contents for HOT-555

Reviews:

Related manuals for HOT-555

Brands by name

Popular brands

Shuttle HOT-555, User Manual

Search results

Summary of Contents for HOT-555

Reviews:

Related manuals for HOT-555

Brands by name

Popular brands