Shuttle HOT-555 User Manual Download Page 26

Page: 26 / 32

HOT-555 User's Manual 26

This function is enabled for only the VGA card

supporting DPM.

Doze Mode

1 Min~1 Hr

Defines the continuous idle time before the sys-
tem entering DOZE mode.

Disable

System will never enter DOZE mode.

Standby Mode

1 Min~1 Hr

Defines the continues idle time before the sys-
tem entering STANDBY mode.

Disable

System will never enter STANDBY mode.

Suspend Mode

1 Min~1 Hr

Defines the continuous idle time before the sys-
tem entering SUSPEND mode.

Disable

System will never enter SUSPEND mode.

HDD Power Down

1~15Min

Defines the continuous HDD idle time before the
HDD entering power saving mode (motor off).

Suspend

BIOS will turn the HDD's motor off when system

is in SUSPEND mode.

Disable

HDD's

motor will not off.

IRQ3, 5, 8, 12 **Wake-Up Events In Doze & Standby**

If this category sets to Off, the IRQ3, 5, 8 or 12 event's activity will not
reactivates the system from Doze and Standby mode.

If this category sets to On, the IRQ3, 5, 8 or 12 event's activity will
reactivate system from Doze and Standby mode.

*Power Down & Resume Events **

If these categories sets to Off, the event's activity will not be monitored to
enter power management.

If this category sets to On, the event's activity will be monitored to enter
power management.

COM Post Accessed

LPT Ports Accessed

Drive Ports Accessed IRQ 3 (COM 2)

IRQ 4 (COM1)

IRQ 5 (LPT 2)

IRQ 6 (Floppy Disk)

IRQ 7 (LPT 1)

IRQ 8 (RTC Alarm)

IRQ 9 (IRQ 2

Redir) IRQ 10 (Reserved)

IRQ 11 (Reserved)

IRQ 12 (PS/2 Mouse) IRQ 13(Copro-)

IRQ 14 (Hard

Disk) IRQ 15 (Reserved)

Summary of Contents for HOT-555

































Search results

Summary of Contents for HOT-555

Reviews:

Related manuals for HOT-555

Brands by name

Popular brands

Shuttle HOT-555, User Manual

Search results

Summary of Contents for HOT-555

Reviews:

Related manuals for HOT-555

Brands by name

Popular brands