Shuttle HOT-555 User Manual Download Page 17 | Manualshive

Page: 17 / 32

background image

HOT-555 User's Manual 17

Load Setup Defaults

Setup defaults loads the values required by the system for the minimum
performance. However, you may change the parameter through the Setup
Menu.

Integrated Peripherals

This setup page includes all the items of peripheral features.

IDE HDD auto detection

Automatically configure IDE hard disk drive parameters.

Supervisor Password

Change, set, or disable supervisor password. It allows you to limit access to
the system and Setup, or just to Setup.

User Password

Change, set, or disable user password. It allows you to limit access to the
system and Setup, or just to Setup.

Save & Exit setup

Save CMOS value change to CMOS and exit setup

Exit without saving

Abandon all CMOS value changes and exit setup.

«
...
15
16
17
18
19
...
»

Summary of Contents for HOT-555

































Reviews:

No comments

Related manuals for HOT-555

ITX-945GC3B N330

Brand: OEM Pages: 38

Altera Lark Board

Brand: Embest Pages: 9

CLICKER 4 for STM32

Brand: Mikroe Pages: 16

Brand: Supermicro Pages: 142

Brand: Supero Pages: 80

Brand: Fairchild Pages: 17

Kontron pITX-iMX8M

Brand: S&T Pages: 65

Brand: MINN KOTA Pages: 16

Brand: Advantech Pages: 88

Brand: CHAINTECH Pages: 49

Brand: Micronics Pages: 80

Brand: Intel Pages: 112

Brand: ASROCK Pages: 106

Brand: Supermicro Pages: 107

Brand: Outboards Group Pages: 44

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands