Shuttle HOT-555 User Manual Download Page 21 | Manualshive

Page: 21 / 32

background image

HOT-555 User's Manual 21

Boot Up NumLock Status

When this option enables, BIOS turns on

Num Lock

when system is

powered on so the end user can use the arrow keys on both the numeric
keypad and the keyboard.

Boot Up System Speed

This option sets the speed of the CPU at system boot time. The settings are

High

or

Low

.

Gate A20 Option

When this category sets to Normal, the A20 signal is controlled by keyboard
controller. When this category sets to Fast, the A20 signal is controlled by
post 92 or chipset specific method.

Security Option

This category allows you to limit access to the system and Setup, or just to
Setup.

When

System

is selected, the system will not boot and access to Setup will be

denied if the correct password is not entered at the prompt.
When

Setup

is selected, the system will boot, but access to Setup will be

denied if the correct password is not entered at the prompt.

PS/2 Mouse Control Function

This category to set the PS/2 mouse be used or not. If there a PS/2 mouse
attached to your system, this category must be enabled, if not, please
disabled this category to release IRQ12 for PCI device.

PCI VGA Palette Snoop

This category must be set to enabled if there is any ISA VGA adapter card
installed in the system, and disabled if there is any PCI VGA adapter card
installed in the system.

OS Select For DRAM > 64MB

If there over 64MB memory on your system, please set this category to

OS2

for total memory detection under OS/2 operating system, otherwise set to

Non-OS2

.

Video BIOS Shadow/XXXXX-XXXXX Shadow

These categories determine whether Video BIOS or optional ROM will be
copied to RAM.

«
...
19
20
21
22
23
...
»

Summary of Contents for HOT-555

































Reviews:

No comments

Related manuals for HOT-555

Brand: IBM Pages: 357

Brand: Quectel Pages: 34

Industrial NUC-J6412

Brand: ASROCK Pages: 2

PowerSoC CY3267

Brand: Cypress Pages: 12

EZ-USB HX2LP CY4605

Brand: Cypress Pages: 2

ITX-945GC3B N330

Brand: OEM Pages: 38

Altera Lark Board

Brand: Embest Pages: 9

Brand: Gigabyte Pages: 40

Brand: Gigabyte Pages: 93

Brand: JETWAY Pages: 46

Brand: Aaeon Pages: 50

MT9M031I12STCH-GEVB

Brand: ON Semiconductor Pages: 5

Brand: Texas Instruments Pages: 27

Brand: Gigabyte Pages: 96

Brand: Supermicro Pages: 84

Brand: JETWAY Pages: 48

Freescale MCIMX6Q-SL

Brand: NXP Semiconductors Pages: 37

Brand: ECS Pages: 87

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands