Shuttle HOT-555 User Manual Download Page 15 | Manualshive

Page: 15 / 32

background image

HOT-555 User's Manual 15

HOT-555's BIOS ROM has a built-in Setup program that allows users to
modify the basic system configuration. This type of information is stored in
battery-backed RAM so that it retains the Setup information when the
power is turned off.

Entering Setup

Power on the computer and press <Del> immediately will allow you to
enter Setup. The other way to enter Setup is to power on the computer,
when the below message appear briefly at the bottom of the screen
during the POST (Power On Self Test), press <Del> key or
simultaneously press <Ctrl>,<Alt>, and <Esc> keys.

TO ENTER SETUP BEFORE BOOT PRESS CTRL-ALT-ESC OR DEL KEY

If the message disappears before you respond and you still wish to enter
Setup, restart the system to try again by turning it OFF the ON or
pressing the "RESET" button on the system case. You may also restart
by simultaneously press <Ctrl>,<Alt>, and <Delete> keys. If you do not
press the keys at the correct time and the system does not boot, an error
message will be displayed and you will again be asked to,

PRESS F1 TO CONTINUE, CTRL-ALT-ESC OR DEL TO ENTER SETUP

Chapter

4

Award BIOS Setup

«
...
13
14
15
16
17
...
»

Summary of Contents for HOT-555

































Reviews:

No comments

Related manuals for HOT-555

Brand: IEI Technology Pages: 234

Brand: Yamaha Pages: 87

Brand: Biostar Pages: 53

Brand: Safran Pages: 26

945GC MICRO 775

Brand: Biostar Pages: 49

H470 AORUS PRO AX

Brand: Gigabyte Pages: 52

Brand: Renesas Pages: 6

Z68A-G43 G3 Series

Brand: MSI Pages: 152

Brand: JETWAY Pages: 58

Brand: Dynatem Pages: 57

Brand: Intel Pages: 36

LMQ61460EVM-400K

Brand: Texas Instruments Pages: 20

Brand: Acorp Pages: 27

Brand: ASROCK Pages: 145

Brand: Yamaha Pages: 50

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 104

Brand: Yamaha Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands