Shinko AER-101-ORP Instruction Manual Download Page 49

Page: 49 / 84

Character

Setting Item, Function, Setting Range

Factory Default

Transmission output status in
Adjustment mode, Span sensitivity
correction mode

Last value HOLD

• Selects Transmission output status in Adjustment mode or Span

sensitivity correction mode.

• Available only when Transmission output (TA option) is ordered.
• Selection range

: Last value HOLD (Retains and outputs the last value

before adjustment or span sensitivity correction.)

Set value HOLD (Outputs the value set in [Set value HOLD].)

: Measured value (Outputs the value measured in

Adjustment mode or Span sensitivity correction mode.)

Set value HOLD

ORP transmission: 0 mV

MV transmission: 0.0%

• Sets the Set value HOLD.
• Available only when

(Set value HOLD) is selected in

[Transmission output status in Adjustment mode, Span sensitivity
correction mode].

• Setting range: ORP transmission: -2000 to 2000 mV

MV transmission: 0.0 to 100.0%

Backlight selection

All are backlit

• Selects the display to backlight.
•

: All are backlit.
: ORP Display
: Setting Display
: Action indicators
: ORP D Setting Display
: ORP D Action indicators
: Setting D Action indicators

ORP color

Red

• Selects a color for the ORP Display.
•

: Green
: Red
: Orange
: ORP color changes continuously.

The ORP Display color changes according to [ORP color
reference value] and [ORP color range] settings.

• When ORP is lower than [ORP color reference value] –

[ORP color range]: Orange

• When ORP is within [ORP color reference value]

[ORP

color range]: Green

• When ORP is higher than [ORP color reference value] +

[ORP color range]: Red

(Fig. 7.7-1)

Orange

Green

Red

: ORP color reference value

: ORP color range

Hys Hys

Hys

Summary of Contents for AER-101-ORP





















































































Search results

Summary of Contents for AER-101-ORP

Reviews:

Related manuals for AER-101-ORP

Brands by name

Popular brands

Shinko AER-101-ORP, Instruction Manual

Search results

Summary of Contents for AER-101-ORP

Reviews:

Related manuals for AER-101-ORP

Brands by name

Popular brands